# Dual-channel Audio Signal Generator

Generate independent left/right waveforms, sweeps, noise or silence as a stereo WAV.

> Canonical page: https://test.elysiatools.com/en/tools/audio-dual-channel-signal-generator

- **Category:** Media

- **Keywords:** stereo, test signal, phase, waveform

## Overview

The same seed reproduces noise. Channel phase and level are independent. Lower amplifier and headphone volume before playback; no automatic playback. Levels are peak targets from −60 to −3 dBFS, not calibrated dB SPL. PCM24 WAV uses an exact frame count rounded from duration × sample rate. Periodic frequencies must stay below 0.45 × sample rate. Square, triangle and sawtooth waves use at most 16 harmonics below that limit with conservative peak normalization. Fades may occupy at most half the active signal. Noise and silence ignore frequency, phase and sweep controls. Excitation is a test input, not a measured room impulse response; a separate recording and deconvolution stage is required.

## Inputs

- **Sample rate** (select)
- **Active duration (seconds)** (number)
- **Fade (ms)** (number)
- **Noise seed** (number)
- **Left waveform** (select)
- **Left start frequency (Hz)** (number)
- **Left end frequency (Hz)** (number)
- **Left sweep** (select)
- **Left phase (degrees)** (number)
- **Left level (dBFS)** (number)
- **Right waveform** (select)
- **Right start frequency (Hz)** (number)
- **Right end frequency (Hz)** (number)
- **Right sweep** (select)
- **Right phase (degrees)** (number)
- **Right level (dBFS)** (number)

## When to use

- Testing stereo balance, channel separation, or crosstalk across studio monitors, headphones, and audio interfaces.
- Evaluating polarity and phase cancellation between stereo channels using calibrated relative phase offsets.
- Generating repeatable excitation tones, sweeps, or seeded noise bursts for acoustic bench tests and equipment calibration.

## How it works

- Select your target sample rate (44.1 kHz, 48 kHz, or 96 kHz), total duration, fade envelope, and noise seed.
- Configure left and right channel parameters independently, choosing waveforms (sine, square, triangle, sawtooth, noise, or silence), frequency bounds, sweep type, phase offset, and peak dBFS level.
- The generator synthesizes band-limited waveforms with conservative normalization and exact frame counts directly into a downloadable 24-bit stereo WAV file.

## Use cases

- Channel isolation verification by generating tone or seeded noise on one channel while keeping the other channel completely silent.
- Acoustic phase cancellation checks by outputting identical sine tones with a 180-degree phase shift between left and right.
- Audio hardware linearity checks using logarithmic frequency sweeps from 20 Hz to 20 kHz on both channels simultaneously.

## Frequently asked questions

### What audio format does the generator produce?

It outputs an uncompressed 24-bit stereo PCM WAV file with exact sample frame counts based on your chosen duration and sample rate.

### Are the output dBFS levels equivalent to sound pressure level (dB SPL)?

No, levels represent digital peak targets between −60 and −3 dBFS, not calibrated physical sound pressure levels.

### Why are harmonics limited on square, triangle, and sawtooth waves?

Non-sinusoidal waveforms synthesize a maximum of 16 harmonics below 0.45 times the sample rate to prevent digital aliasing.

### Can I reproduce the exact same noise signal later?

Yes, using the exact same noise seed value reproduces identical pseudo-random noise sequences across generations.

### Do frequency, phase, and sweep settings affect noise or silence?

No, frequency, sweep, and phase controls are completely bypassed when a channel is set to noise or silence.

## Related tools

- [Audio Chirp Sweep Generator](https://test.elysiatools.com/en/tools/audio-chirp-sweep-generator): Generate phase-integrated linear or logarithmic sine sweeps as a mono WAV.
- [Audio Waveform Generator](https://test.elysiatools.com/en/tools/audio-waveform-generator): Generate a waveform image from an audio file
- [Stereo Signal Tone Generator](https://test.elysiatools.com/en/tools/stereo-signal-tone-generator): Generate a stereo test tone file with independent left and right channel frequency, phase, waveform, and level controls.
- [Normalization History Card](https://test.elysiatools.com/en/tools/audio-normalization-history-card): Generate a shareable before/after report card for any loudness change: gain applied, LUFS, true peak, sample peak, loudness range, waveforms and third-octave spectral deltas.
- [Audio to Waveform Video](https://test.elysiatools.com/en/tools/audio-to-waveform-video): Create a video from audio with a waveform visualization
- [Audio Balance](https://test.elysiatools.com/en/tools/audio-balance): Free online audio balance adjuster: fix a louder left or right channel. Set each channel from 0% to 400% and download the corrected stereo audio as MP3, WAV, or FLAC.
- [Invert Channel Phase](https://test.elysiatools.com/en/tools/audio-invert-phase): Free online phase inverter: flip the phase of the left, right, or both channels of a stereo audio file for vocal reduction or creative stereo effects. Upload MP3, WAV, FLAC and more, up to 100 MB.
- [Audio Vocoder](https://test.elysiatools.com/en/tools/audio-vocoder): Turn a voice or instrument recording into a robotic audio effect with a built-in carrier. Set the blend and export as MP3, WAV, or five other audio formats.

## Samples

- [Copyright-Free MP3 Audio Samples](https://test.elysiatools.com/en/samples/mp3-samples): Collection of royalty-free audio samples for testing and development purposes including nature sounds, meditation music, and ambient audio
- [Copyright-Free WAV Audio Samples](https://test.elysiatools.com/en/samples/wav-samples): Uncompressed PCM WAV audio samples for testing and development, mirrored from MP3 set with nature sounds and meditation music
- [Copyright-Free Raw PCM Audio Samples](https://test.elysiatools.com/en/samples/pcm-samples): Raw PCM s16le audio samples featuring nature ambience and relaxing music for waveform, playback, and conversion workflows
- [Speech Learning & Safety Audio Samples](https://test.elysiatools.com/en/samples/audio-learning-safety-samples): Deterministic synthetic WAV inputs for pronunciation comparison, dictation preflight, alert degradation, and voice privacy tools.

## Related content

- [Audio Processing Regression Tests: Null, Distortion and Report Handoff](https://test.elysiatools.com/en/hubs/audio-processing-regression-null-and-distortion-review): Compare a fixed audio reference with separately processed outputs, document null-test coverage and suitable single-tone THD results, and deliver a reviewed regression record with files and hashes.
- [Audio Test Signal Generation, Review and Handoff](https://test.elysiatools.com/en/hubs/audio-test-signal-generation-review-and-handoff): Create sweep, stereo or measurement-excitation fixtures, check their format and expected signal behavior, and hand off parameters, review evidence and file hashes without claiming a measured acoustic response.
