# Rapidity Calculator

φ = artanh(β) with γ = cosh φ, γβ = sinh φ, the e^φ Doppler factor, and the tanh(2φ) additivity check — where boosts just add.

> Canonical page: https://test.elysiatools.com/en/tools/rapidity-calculator

- **Category:** Science & Education

- **Keywords:** rapidity, hyperbolic angle, artanh, boost composition, doppler factor, special relativity

## Overview

The Rapidity Calculator computes the relativistic rapidity φ = artanh(β) from velocity, transforming non-linear Lorentz velocity additions into simple linear additions. It instantly outputs key relativistic parameters including the Lorentz factor γ = cosh(φ), proper velocity component γβ = sinh(φ), the longitudinal Doppler factor e^φ, and the doubled boost composition tanh(2φ).

## Inputs

- **Speed input** (select)
- **β (v/c)** (number): e.g. 0.5
- **Speed v (m/s)** (number): e.g. 1.5e8

## When to use

- When composing successive collinear relativistic boosts where rapidities add linearly instead of using Einstein's velocity addition formula.
- When calculating relativistic Doppler factors (redshift/blueshift multipliers) or Lorentz gamma values directly from a particle's speed.
- When analyzing high-energy particle kinematics and accelerator beam coordinates where speeds approach the speed of light.

## How it works

- Select the input format: either dimensionless fraction of the speed of light (β = v/c) or speed in meters per second (m/s).
- Enter the velocity value into the corresponding field, such as a fraction of c (e.g., 0.5) or physical speed.
- The tool evaluates the hyperbolic angle φ = artanh(β) using the natural logarithm form ½·ln((1+β)/(1−β)).
- It displays the computed rapidity φ, γ = cosh(φ), γβ = sinh(φ), Doppler factor e^φ, and the composite velocity tanh(2φ).

## Use cases

- High-energy particle physics calculations for composing consecutive particle collisions and beam boosts.
- Special relativity coursework and verification of relativistic velocity addition and hyperbolic kinematics.
- Relativistic astrophysics problems involving longitudinal Doppler shifts and relativistic jets.

## Frequently asked questions

### What is rapidity in special relativity?

Rapidity φ is a hyperbolic angle defined as φ = artanh(v/c). Unlike velocities, collinear rapidities add linearly when chaining Lorentz boosts.

### How does rapidity relate to the Lorentz factor γ?

The Lorentz factor γ is given by the hyperbolic cosine of rapidity: γ = cosh(φ), while γβ corresponds to sinh(φ).

### What is the Doppler factor e^φ?

The term e^φ represents the relativistic longitudinal Doppler factor, indicating the exact frequency shift ratio for an approaching or receding source.

### Can rapidity exceed 1?

Yes. While β is strictly bounded between -1 and 1 (subluminal speeds), rapidity φ ranges from -∞ to +∞ as β approaches ±1.

### What does tanh(2φ) represent in the output?

tanh(2φ) represents the combined velocity (as a fraction of c) resulting from two consecutive reference frame boosts of the same rapidity φ.

## Related tools

- [Snell's Law Calculator](https://test.elysiatools.com/en/tools/snell-law-calculator): n₁·sinθ₁ = n₂·sinθ₂ for either angle, with the total-internal-reflection regime and critical angle when sinθ exceeds 1.
- [Heisenberg Uncertainty Principle Calculator](https://test.elysiatools.com/en/tools/uncertainty-principle-calculator): Δx·Δp ≥ ℏ/2: minimum Δp from Δx, minimum Δx from Δp, or a pair check with satisfaction ratio. Units m–pm and kg·m/s / g·cm/s / eV/c; optional mass derives Δv.
- [Shapiro-Wilk, Anderson-Darling and Lilliefors Normality Tutor](https://test.elysiatools.com/en/tools/shapiro-wilk-anderson-darling-lilliefors-normality-tutor): Run the three workhorse normality tests (Shapiro-Wilk AS R94, Anderson-Darling, Lilliefors) with a Q-Q plot and a Monte-Carlo power comparison.
- [Arrhenius Equation Calculator](https://test.elysiatools.com/en/tools/arrhenius-equation-calculator): k = A·e^(−Ea/RT) solved for k, A, or Ea (two-point form), with Ea in kJ/mol and kcal/mol.
- [Boiling Point Elevation](https://test.elysiatools.com/en/tools/boiling-point-elevation): ΔT_b = K_b·m·i from a solvent preset table with van't Hoff factor support and custom solvents.
- [Conductivity Cell Constant Calculator](https://test.elysiatools.com/en/tools/conductivity-cell-constant): K = κ/G and κ = K·G with unit selectors for κ, G and K — calibrate the cell or convert a reading into conductivity.
- [Electric Field of a Point Charge](https://test.elysiatools.com/en/tools/electric-field-point-charge): E = k·|Q|/r² in N/C with charge and distance unit selectors, the radial direction from the sign of Q, and the force an electron would feel at that point.
- [Mass-Energy Equivalence Calculator](https://test.elysiatools.com/en/tools/energy-mass-conversion): E = mc² both ways: mass to rest energy (J, kWh, eV-scale, TNT) and energy to mass (kg, g, u, electron masses).

## Samples

- [Web Image Processing Python Samples](https://test.elysiatools.com/en/samples/web-image-processing-python): Web Python image processing examples using PIL/Pillow including reading, saving, resizing, and format conversion
- [Android Image Processing Java Samples](https://test.elysiatools.com/en/samples/android-image-processing-java): Android Java image processing examples including reading/saving images, scaling, and format conversion
- [Android Image Processing Kotlin Samples](https://test.elysiatools.com/en/samples/android-image-processing-kotlin): Android Kotlin image processing examples including reading/saving images, scaling, and format conversion
- [Web Image Processing Rust Samples](https://test.elysiatools.com/en/samples/web-image-processing-rust): Web Rust image processing examples including image read/save, scaling, and format conversion
